Skip to content
PERCH & POSTURE

TRALT office chair: the shortest seat pan here, checked against its own claim

TRALT says this chair suits 5 ft 4 in to 6 ft 2 in. Its own published seat depth does not support the bottom of that window, and the arithmetic takes about a minute.

By Sawyer V. · Published November 1, 2026

We earn a commission if you buy through the links on this page, at no extra cost to you. It does not affect the order of the picks - the rubric does that, and here is how we are funded. Prices were last verified November 17, 2026.

What we did and did not do

Units we claim to have tested: 0. Everyone in this category says they tested twenty chairs. We have not sat in any of these, and we say so.

What we did instead: compiled every figure each manufacturer publishes, computed the fit ranges from a cited anthropometric table, and linked the source for each number so you can check the arithmetic. Where a manufacturer does not publish a figure, we say that rather than filling the gap. The full method, including what we cannot assess, is here.

TRALT publishes a 17.3 in seat depth, and that is the shortest seat pan of any task chair on this site. It matters more than it sounds. Seat depth is the dimension that decides whether the front edge of the chair presses into the back of your knee, and it is the one measurement most listings in this price bracket leave out entirely. TRALT states it, states a 19.7 in seat width, states a 17.7 to 21.7 in height range, states 330 lb, states a two-year warranty and names the gas cylinder class. That is a more complete sheet than most chairs costing the same.

It also makes a fit claim that its own figures do not fully support. The listing says the chair suits users from approximately 5 ft 4 in to 6 ft 2 in. The top of that window holds up. The bottom does not, and the gap is the seat pan - the very figure TRALT deserves credit for publishing. We check it below against the same anthropometric table every other page on this site uses.

Buy it if you are between roughly 5 ft 6 in and 6 ft 1 in, you want a short seat pan in writing rather than inferred, and a published capacity and cylinder class matter to you. Buy the SONGMICS instead if price is the deciding factor - it publishes the identical 17.7 to 21.7 in range and slightly more capacity for about two-thirds of the money, and the thing you give up is the seat-depth figure. Buy the CAPOT instead if you want lumbar adjustment you can count in inches, because that is the one criterion where TRALT markets a feature and publishes no number for it.

What TRALT publishes

Every figure from TRALT's own listing, with the blanks named rather than filled in. Live price is on the card below.
FigurePublished valueRubric criterion
Seat-height range17.7-21.7 in, 4 in of travelFit range
Seat depth17.3 in - shortest task-chair pan hereFit range
Seat width19.7 inFit range
Rated capacity330 lbCapacity headroom
Gas cylinderBIFMA-certified Class 3, anti-sinkMaterials and build
BaseReinforced nylon with a metal core, 360-degree castersMaterials and build
BackrestHigh-tension meshMaterials and build
Seat foamHigh-resilience molded foamMaterials and build
Warranty2 yearsCost per warranty year
CertificationBIFMA basic durability and safetyMaterials and build
AssemblyStated at 15 minutes-
HeadrestNone - deliberately omitted, and TRALT says soAdjustability
Lumbar adjustment travelNot published - depth adjustment claimed, no figureAdjustability
Armrest adjustmentNot publishedAdjustability
Recline or tilt rangeNot publishedAdjustability

Twelve answered lines against three blanks is well above average for this price bracket, and the shape of the split is the interesting part. Everything that decides whether the chair physically fits you is stated: height, depth, width, capacity. Everything that decides how much you can tune it once you are sitting in it - lumbar travel, armrest movement, recline - is either absent or, in the case of the headrest, deliberately left out and explained. That is an unusually forthcoming listing in one direction and a silent one in the other.

Does it fit you? TRALT says 5 ft 4 in to 6 ft 2 in

That is the maker's own claim, and it is worth checking rather than repeating. Here is the table this site computes from published popliteal-height and buttock-popliteal-length percentiles - the same table behind every fit call we make:

Seat height and depth by your height

Computed from published popliteal-height and buttock-popliteal-length percentiles (Pheasant & Haslegrave, Bodyspace). Seat height includes a 1 in shoe allowance.
Your heightSeat heightMax seat depthStanding-desk height
5'0"15-16.6 in15.6 in37.8 in
5'2"15.7-17.3 in16.7 in39.1 in
5'4"16.3-17.9 in16.7 in40.2 in
5'6"17-18.6 in17.7 in41.4 in
5'8"17.9-19.5 in19.9 in42.8 in
5'10"18.4-20 in18.8 in44.2 in
6'0"19.1-20.7 in19.8 in45.6 in
6'2"19.5-21.1 in20.4 in46.5 in
6'4"19.5-21.1 in20.4 in46.5 in
6'6"19.5-21.1 in20.4 in46.5 in

Start at the bottom of TRALT's window, 5 ft 4 in. You want a seat height of about 16.3 to 17.9 in, and the chair's floor is 17.7 in - inside the window, but in the top fifth of it, with essentially no room to go lower. Now read across to the next column: at 5 ft 4 in the maximum seat depth is 16.7 in, and TRALT's pan is 17.3 in. That is roughly half an inch too deep, and seat depth does not adjust on this chair. The front edge sits against the back of the knee - the exact thing OSHA tells you to avoid, and the reason we check depth at all.

Move up to 5 ft 6 in and the chair comes right. The window is 17 to 18.6 in, so the 17.7 in floor now sits comfortably inside it, and the maximum depth rises to 17.7 in - which clears the 17.3 in pan with a little to spare. On this site's arithmetic, the honest floor for this chair is about 5 ft 6 in, not the 5 ft 4 in TRALT claims. It is a two-inch difference and it is the single most useful thing on this page.

The top of the claim holds. At 6 ft 2 in you want roughly 19.5 to 21.1 in and can take a pan up to about 20.4 in deep; the chair reaches 21.7 in and its pan is shallower than that maximum, which costs you some thigh support but does not press anywhere. One honest caveat on that figure: the published anthropometric table this site uses tops out a shade above 6 ft 1 in, so 6 ft 2 in is the last row it genuinely computes rather than repeats. Above that we would not claim a number.

This is also why the chair appears at opposite ends of two of our pages. It is the top pick on our page for petite and shorter users, where the short pan is the scarcest thing in the field, and it is excluded from the tall-user page for the same two numbers read the other way round.

The lumbar claim, without a number

TRALT's listing leads on lumbar support: it describes an adjustable mechanism that moves in depth to match the curve of your spine, and contrasts it with fixed plastic supports that crack. It never says how far it travels. On a criterion where the adjustment is the product, a claim without a figure cannot be compared against anything, and we score it accordingly.

The contrast on this site is direct rather than theoretical. The CAPOT OC.018 publishes 2 in of lumbar travel over eight levels - you can count the detents and you can check the span. That is why the CAPOT holds the lumbar-led pages here and why it sits at rank 3 on this one despite being the better-specified chair overall. Whether the TRALT's lumbar moves a useful amount is genuinely unknown from the listing, and we are not going to guess at it. Whether lumbar support helps at all is a separate question we answer here.

Capacity, the cylinder, and what BIFMA does and does not mean

330 lb is a genuinely high rating for a chair in this bracket, and TRALT pairs it with a reinforced nylon base with a metal core rather than the all-plastic hub that usually fails first. It also names a BIFMA-certified Class 3 gas cylinder, which is the part of the chair that quietly sinks under you when it is cheap. Naming the cylinder class is rare at this price and it is the most checkable build claim on the listing.

Two things to keep straight. TRALT states BIFMA basic durability and safety certification, not a full ANSI/BIFMA X5.1 pass under a named protocol - and X5.1 itself tests around a 275 lb occupant, so a 330 lb rating is the maker's figure rather than a standard's. Our working rule across this site is that a chair suits a user up to roughly 80 percent of its stated rating. How to read a chair spec sheet, including which certifications mean what, is covered here.

The chair that undercuts it

The strongest argument against this chair is on our own list. The SONGMICS mesh chair publishes exactly the same 17.7 to 21.7 in seat-height range, the same 19.7 in seat width, a slightly higher 331 lb capacity and a 3.5 in seat cushion - for about two-thirds of the money. We are not going to talk around that.

The three chairs this decision comes down to, on published figures only. Live prices are on each card below.
Seat heightSeat depthCapacityLumbar travelPrice bracket
TRALT17.7-21.7 in17.3 in330 lbClaimed, not statedMiddle of the three
SONGMICS17.7-21.7 inNot published331 lbClaimed, not statedAbout two-thirds of the TRALT
[CAPOT OC.018](/reviews/capot-ergonomic-mesh-chair)18.5-22.05 in19.3 in400 lb2 in over 8 levelsHighest of the three

So what is the premium buying? One figure: the seat depth. If you are near the short end of this chair's real window, that figure is the whole reason to choose it - the SONGMICS might have the same pan or a deeper one and you cannot tell from its listing, and an unknown pan on a short user is a coin flip. If you are comfortably in the middle of the range, where pan depth is not the binding constraint, the premium is buying you information you do not need, and the cheaper chair is the better buy. That is an unsatisfying answer and it is the true one.

Should you buy it?

If you are between about 5 ft 6 in and 6 ft 1 in, yes, on the figures. You get the shortest published task-chair pan on this site, a high rated capacity, a named cylinder class and a two-year warranty, from a listing that states most of what you need and admits what it leaves out. For a chair in this bracket that is a good trade.

If you are 5 ft 4 in or under, this is not the chair the listing says it is - the pan is about half an inch too deep on our arithmetic, and no adjustment on it closes that gap. Read the petite-user page first, because the honest answer in that case involves a footrest regardless of which chair you buy. And if what you actually want is lumbar adjustment you can verify, the figure you are looking for is published by a different chair.

The chair under review, and the two it competes with

Ranked on the published rubric. Tap a row for the full write-up; the price button goes straight to Amazon. Every figure in the write-ups is the manufacturer's own published specification, linked at the source. We have not sat in any of these.

Scores out of 10. Published seat-height range and seat depth, against the lumbar travel the listing never states.
#ProductBest forScorePrice
1
TRALT Ergonomic Chair with Adjustable Lumbar

TRALT Ergonomic Chair with Adjustable Lumbar

The Chair Under Review

A 17.3 in seat pan8.4
$119.99 - View on Amazon

#ad disclosure · November 17, 2026

2
SONGMICS Ergonomic Mesh Chair

SONGMICS Ergonomic Mesh Chair

The Cheaper One With the Same Range

An identical 17.7-21.7 in, for less7.4
$79.99 - View on Amazon

#ad disclosure · November 17, 2026

3
CAPOT OC.018 Ergonomic Mesh Chair

CAPOT OC.018 Ergonomic Mesh Chair

The One That Publishes the Missing Figure

2 in of counted lumbar travel9.4
$199.99 - View on Amazon

#ad disclosure · November 17, 2026

01 · The Chair Under Review

TRALT Ergonomic Chair with Adjustable Lumbar

8.4/10 · scored on the published rubric

A 17.3 in seat depth is the shortest published here, and our arithmetic says that is what makes it work for shorter users - it clears the back of the knee from about 5 ft 6 in, where every deeper pan here does not.

Why you might not: A 21.7 in ceiling rules it out above roughly 6 ft, and TRALT states lumbar adjustment without saying how far it travels.

Published figures, from the TRALT listing. Blank rows below are figures the manufacturer does not publish.
Seat height17.7-21.7 in
Seat depth17.3 in
Seat width19.7 in
Rated capacity330 lb
Warranty2 years
Cost per warranty year$60.00
Maker's stated user height5 ft 4 in to 6 ft 2 in

Adjustments published (3): seat height (17.7-21.7 in); adjustable lumbar; BIFMA Class 3 gas cylinder.

Not published by the manufacturer: lumbar travel in inches. We have flagged these rather than guessed.

How this score was built
  • Fit range9/10
  • Adjustability7/10
  • Capacity headroom9/10
  • Materials & warranty8/10
  • Spec coverage9/10

The overall is the mean of these, rounded to one decimal place. Each criterion is computed from a published figure - the rubric is here.

TRALT Ergonomic Chair with Adjustable Lumbar
$119.99 - View on Amazon

Price as of November 17, 2026. #ad how this is funded

02 · The Cheaper One With the Same Range

SONGMICS Ergonomic Mesh Chair

7.4/10 · scored on the published rubric

331 lb and a published 3.5 in cushion at the lowest price of any chair on this site that publishes a seat-height range at all.

Why you might not: The recline stops at 105 degrees, which is barely a recline, and the seat depth is not published - the one figure a shorter user most needs.

Published figures, from the SONGMICS listing. Blank rows below are figures the manufacturer does not publish.
Seat height17.7-21.7 in
Seat width19.7 in
Thickness3.5 in
Rated capacity331 lb

Adjustments published (4): seat height (17.7-21.7 in); flip-up armrests; tilt 90-105 degrees; lumbar support.

Not published by the manufacturer: seat depth; warranty term. We have flagged these rather than guessed.

How this score was built
  • Fit range8/10
  • Adjustability7/10
  • Capacity headroom9/10
  • Materials & warranty7/10
  • Spec coverage6/10

The overall is the mean of these, rounded to one decimal place. Each criterion is computed from a published figure - the rubric is here.

SONGMICS Ergonomic Mesh Chair
$79.99 - View on Amazon

Price as of November 17, 2026. #ad how this is funded

03 · The One That Publishes the Missing Figure

CAPOT OC.018 Ergonomic Mesh Chair

9.4/10 · scored on the published rubric

The only chair on this site that answers all six rubric criteria from published figures: seat range, depth, width, 400 lb capacity, a five-year warranty and eight levels of 2 in lumbar travel - which also gives it the lowest cost per warranty year of any task chair here.

Why you might not: It tops out at 22.05 in. If you are over about 6 ft 2 in you will run out of seat height, whatever the listing's stated window says.

Published figures, from the CAPOT listing. Blank rows below are figures the manufacturer does not publish.
Seat height18.5-22.05 in
Seat depth19.3 in
Seat width20 in
Rated capacity400 lb
Warranty5 years
Cost per warranty year$40.00
Maker's stated user height5 ft 5 in to 6 ft 2 in

Adjustments published (5): seat height (18.5-22.05 in); lumbar depth (2 in over 8 levels); backrest lock at 90, 110 and 125 degrees; headrest height and depth; armrests flip up 90 degrees.

How this score was built
  • Fit range7/10
  • Adjustability10/10
  • Capacity headroom10/10
  • Materials & warranty10/10
  • Spec coverage10/10

The overall is the mean of these, rounded to one decimal place. Each criterion is computed from a published figure - the rubric is here.

CAPOT OC.018 Ergonomic Mesh Chair
$199.99 - View on Amazon

$224.99 list, 11% off

Price as of November 17, 2026. #ad how this is funded

Questions people actually ask

What is the TRALT office chair's seat height range?
17.7 to 21.7 in, published by TRALT - 4 in of travel on a BIFMA-certified Class 3 gas cylinder. That floor is the figure that decides whether it suits a shorter user, and only one task chair on this site publishes a lower one.
Does the TRALT office chair really fit someone 5 ft 4 in?
Not on our arithmetic. At 5 ft 4 in the maximum seat depth is about 16.7 in and the TRALT's pan is 17.3 in, so the front edge meets the back of the knee. The seat height works at that stature; the depth does not, and depth does not adjust on this chair. We put the honest floor at about 5 ft 6 in.
How much lumbar adjustment does the TRALT chair have?
TRALT does not publish a figure. The listing describes a lumbar mechanism that adjusts in depth and contrasts it with fixed supports, but states no travel in inches and no number of levels, so there is nothing to compare it against. The CAPOT OC.018 publishes 2 in over eight levels if that is the criterion you are buying on.
Does the TRALT office chair have a headrest?
No, and unusually the listing explains the omission rather than hiding it - TRALT says it skipped a cheap headrest to spend the budget on the lumbar system, the metal-core base, the certified cylinder and the seat foam. Whether you accept that trade is a judgment call, but it is stated up front.
Is the TRALT chair's 330 lb capacity trustworthy?
It is the manufacturer's figure. TRALT states BIFMA basic durability and safety certification rather than a full ANSI/BIFMA X5.1 pass under a named protocol, and X5.1 tests around a 275 lb occupant. Our working rule is that a chair suits a user up to roughly 80 percent of its stated rating.
Have you tested the TRALT office chair?
No - zero units. Every figure on this page comes from TRALT's own published listing, with the source linked on the card, and the figures that listing omits are named as gaps rather than filled in with estimates. The fit arithmetic comes from published anthropometric percentiles, not from sitting in the chair.

Read next

Sources